Service & Replacement Parts

Fork service kit containing fork seal kit (select either SKF or SRAM), internal seal kit, fork oil, bushing lubricant, Slickoleum assembly grease, oil syringe & optional seal press tool Learn More

Application: 2014-18 RockShox 35 mm Pike/Lyrik/Boxxer forks with Charger RC or RCT3 dampers.

PDF showing contents of kit is available here Learn More

Application: 2018+ RockShox 35 mm Pike/Lyrik/Boxxer forks with Charger 2 or 2.1 RC, Charger RCT3 or RC2 dampers.
Includes o-ring upgrade to replace the cup seal that leaks out the top knobs.

PDF showing contents of kit is available here Learn More

BoXXer Charger 2.1 RC2 damper upgrade kit
Fits 35 mm BoXXer forks 2019+ C1+
Includes complete right side internals

SRAM Part Code: 00.4020.171.000

These dampers are ordered in from the NZ Supplier as required.  Lead time is usually 2 days.

Shockcraft can tune this damper for you before delivery Learn More

RockShox Fork Damper Tune Assembly for Charger 3.1 Contains Piston Tool and Shims for compression/rebound tune configurations. Compatible with BOXXER D1+ (2024+), ZEB A1 + (2021+), LYRIK D1+ (2023+), PIKE C1+ (2023+) SRAM Part Code: 11.4018.136.000 Learn More

SKF Low Friction Flangeless Fork Seal kit for RockShox 35 mm forks Learn More

Original RockShox 35 mm fork seal kit. Fits RockShox Boxxer (2010+), Domain Dual Crown, Lyrik & Pike (2014+) forks Learn More

SKF Low Friction Fork Seal kit for RockShox Boxxer 35 mm forks
Contains 2x wiper seals, 2x oil seals and 2x foam rings

Learn More

8 mm Crush Washer
11mm OD, 1.6mm thick.
Fits Fox, Rockshox & other forks.

Sold indvidually. Learn More

Single foam ring for RockShox 35 mm stanchioned forks Learn More

8mm Crush Washer with 16mm flange
16mm OD, 2mm total thickness  with 1mm flange
Required on Rockshox Boxxer forks with oversize hole in the casting
Also used in Lyrik forks. Learn More

SKF seal head upgrade/replacement for RockShox charger 1 dampers
Fits Pike, Lyrik & Boxxer forks, both RC & RCT3 with Charger 1
Upgrade for early Pike forks built with Trelleborg seal head.
Replacement part for seal head on later model Pike, Lyrik & Boxxer forks

SRAM Part Code: 11.4015.353.030 Learn More

Individual volume spacer for Rockshox 35 & 38 mm forks (Pike, Lyrik, Yari, Zeb, Boxxer etc) with solo air spring (no travel adjust).
SRAM Part Code (for pack of 10): 11.4018.032.001

Learn More

Spare Pair of crush washer retainers for RockShox forks. Fits with 8mm crush washers Learn More

Spare pair of 8 mm crush washers for RockShox & Fox forks Protect lower legs from foot nuts/bolts These are sacrificial and should be replaced whenever fork foot nuts/bolts are removed Learn More

Schrader Valve Core with short 16 mm length
5V1 thread
Part Code: 98-30474

Learn More

Boxxer B1-B2 2015-2019 coil spring Soft - yellow. 37 lb/in. SRAM Part Code: 11.4015.380.010 Learn More

These are only available for Pike, other applications have been superseded by the Debonair C1 (V3).

Superseded by SRAM-LYRIKPIKEDEBONAIR-AIRSHAFTUPV3

Debonair name was used in Solo Air Lyrik and Yari forks in 2018.  We call this Debonair V1.
Debonair V2 was introduced for MY 2019.  It features shafts with higher negative air volume and lower friction than previous Solo-Air air spring shafts.  Visible differences are the red flat seal-head, plastic moulded grey or black piston and removable shaft foot.
This bigger negative volume and lower friction gives you better small bump response and lets you run more air pressure for more mid stroke support.  They are a bolt-in upgrade, but only fit solo-air forks.  Debonair V2 shafts are also available in different lengths if you want to change your fork travel.  Select the correct one for your forks.

These are available for self-install or can be installed as part of a Shockcraft service. Learn More

Debonair V3 (RS calls it Debonair C1) is a new design for mid 2020 release to make bikes ride higher in the travel and use travel more easily.
It is identified by a longer red shaft foot and a red base-plate which is hollow underneath.

These are available for self-install or can be installed as part of a Shockcraft service.  Sizes are specific to each model, generation and travel of fork.

All sizes ordered in from supplier upon customer order.  Usually available approx 2 days lead-time.

V3 are no longer available for Rockshox Pike A1-A2, use RockShox DebonAir V2 Air Shaft Upgrade (SRAM)

Learn More

Rockshox Charger Bladder Assembly for Boxxer B1-B2 (SRAM)
Fits 2015-18 Boxxer World Cup (WC) with Charger 1 dampers.
Total Length Approx 172mm

SRAM Part Code:  11.4018.031.010 Learn More