Bolt-In Upgrades

BoXXer Charger 2.1 RC2 damper upgrade kit
Fits 35 mm BoXXer forks 2019+ C1+
Includes complete right side internals

SRAM Part Code: 00.4020.171.000

These dampers are ordered in from the NZ Supplier as required.  Lead time is usually 2 days.

Shockcraft can tune this damper for you before delivery Learn More

Replacement heat shrink for Vorsprung Smashpot coil springs Learn More

2 piece isolator system helps keep the coil spring quiet and stanchions protected internally when installing the Vorsprung Smashpot coil conversion
Retrofittable to older Smashpot Coil Conversion kits
Can be used in all forks instead of the older style spring perch
Replaces the PVC liner previously used in the RockShox Zeb and Fox 38 kits

Ordered in from NZ supplier upon customer order.  Usually available approx 2 days lead-time. Learn More

Available for use with a Vorsprung Secus RockShox A2 kit on newer RockShox forks with Buttercups. Learn More

IVA: Incremental Volume Adjust A 5 position spacer system to tune positive air chamber volume and increase progression
Thread M31 x 0.8 mm
Finer thread than the Mattoc/Magnum IVA upgrade kit

Manitou Part Code: 141-35384-K006 Learn More

Manitou Mattoc IRT Upgrade Kit 2020+
Adds a second air chamber for independent tuning of mid-end stroke.
Compatible with 2020+ Mattoc Pro, Mastodon Pro & Circus Pro can be fitted to Comp with a piston swap.
Installs with a cassette tool and uses a flatter cap than earlier versions

Manitou part code: 141-32668-K010

Learn More

IVA: Incremental Volume Adjust
A 5 position spacer system to tune positive air chamber volume and increase progression
M32 x 1.0 mm thread

Manitou Part Code: 141-32668-K001

Learn More

IRT: Infinite Rate Tune
Adds a second air chamber for independent tuning of mid-end stroke.
Coarse thread M32x1.0mm for 2014-2019 Mattoc, Magnum, Mastodon Pro and Expert level forks.
Manitou Part Code: 141-32668-K003 Learn More

Manitou Racing Development (MRD) Upgrade kit.
Fits Dorado 2009-2019
Includes Dorado Infinite Rate Tune (IRT) air spring upgrade kit, Trail Side Relief bleeder caps
& high performance MRD wiper seals

Manitou Part Code: 141-32409-K001

Learn More

SKF seal head upgrade/replacement for RockShox charger 1 dampers
Fits Pike, Lyrik & Boxxer forks, both RC & RCT3 with Charger 1
Upgrade for early Pike forks built with Trelleborg seal head.
Replacement part for seal head on later model Pike, Lyrik & Boxxer forks

SRAM Part Code: 11.4015.353.030 Learn More

Shims, balls & springs for DIY tuning of Manitou ABS+ compression dampers
ABS+ tuning guide can be found here
Manitou Part Code: 141-32511-K001

Learn More

Adapter for installing 2014+ RS Pike/Lyrik Solo Air Luftkappe for A2 chassis Pike into 2018 RockShox Pike with B1 chassis.

Note 29+ Pike (2017/18) is built on the Lyrik/Yari B1 chassis and does not require this adapter.

Learn More

Vorsprung Luftkappe air piston and low volume sealhead for Fox 34 NA2 forks
Fits 2016-17 Fox Float 34 NA2 Performance & Factory Series forks (130+ mm only)
Requires shaft clamp to install and is threaded onto air shaft.
Included low volume sealhead increases negative volume similar to 2018 Evol spec
Can be installed as part of any Shockcraft service (book here)

Learn More

Roll pin tool for use in installation of Luftkappe in Fox Float 34 Evol 2018+, 34 NA2 2016-17 & 36 Evol 2018+ forks

Learn More

MILO (Manitou Integrated Lock Out) kit for Kwik Toggle (KT) damper used in 2017+ forks
Kit includes 2 position handle-bar lever, cable, cable housing, fork mounted cable stop, return spring, KT cap and screw
Will adapt any Kwik Toggle fork damper to remote (handlebar) lockout operation
Manitou Part Code: 141-33538

Learn More

Upgrade your Mattoc Expert to Mattoc Pro specification.
Requires the Mattoc Pro rebound shaft assembly
Compression damping requires either the Mattoc Pro MC2 compression assembly or convert your Expert compression damper with the Pro HBO Cup.
27" wheel size for up to 160 mm travel

Manitou Part Codes: 141-30996-K017 (Rebound Assembly) & 141-30996-K001 (Compression Damper Assembly) or 126-30377 (Mattoc Pro HBO Cup)

Learn More

MILO (Manitou Integrated Lock Out) lever kit for rear shock or repair
Kit includes 2 position handle-bar lever, cable & cable housing
Manitou Part Code: 141-31975-K003

Learn More

For upgrade of Mezzer Expert or repair on Mezzer Pro
Adds a second air valve and air chamber for tuning last half of the stroke.

Manitou Part Code: 141-36713-K021 Learn More

Manitou Mattoc Pro 2023 complete damper with Shockcraft Ready Mix Tune
The Ready Mix Tune is our Pick & Mix Self Tune with the picking, mixing and install already done for you

Purchase this tuned damper for easy self-install in your Manitou Mattoc Pro 2023 fork Learn More

Vorsprung Luftkappe extended air piston and low volume sealhead for RockShox Zeb forks
Fits 2021-22 RockShox Zeb forks, fits 2023 Zeb if 2021-22 air shaft installed
Requires 10 mm shaft clamp to install
Can be installed as part of any Shockcraft service (book here)

Learn More

Damper Upgrade Kit CHARGER2.1 RC2 for Zeb A1+ 2021 (SRAM)
Self contained charger2.1 damper for repair or upgrade from sub-par Charger R/RC versions.
Adjustable 4 click High Speed Compression (HSC), 19 click Low Speed Compression (LSC) and Low Speed rebound (LSR)
2021 Zeb A1 only.  Max 200mm travel.
Includes adjuster knobs & foot bolt.

SRAM Part Code: 00.4318.048.000

Shockcraft can tune this damper for you before delivery.  This improves compliance, support and stability.  Details here for purchase of this damper tuned & modified.

Learn More

Replacement Smashpot V1 foot stud assembly to fit DVO Onyx SC forks
Vorsprung Smashpot kits for RockShox, Fox, Öhlins & DVO use the same core assembly (inner & outer) with a different foot stud assembly & top cap
This foot stud assembly can be used to swap a Smashpot from a RockShox, Fox or Öhlins fork to a DVO Onyx SC fork
You will also need the Smashpot top cap for the DVO Onyx SC forks (see related products) Learn More

Replacement Smashpot V1 foot stud assembly to fit Öhlins RFX36 forks
Vorsprung Smashpot kits for RockShox, Fox, Öhlins & DVO use the same core assembly (inner & outer) with a different foot stud assembly & top cap
This foot stud assembly can be used to swap a Smashpot from a RockShox, Fox or DVO fork to an Öhlins RFX36 fork
You will also need the Smashpot top cap for the Öhlins RFX36 forks (see related products) Learn More

Replacement Hydraulic Bottom Out (HBO) adjuster knob for Vorsprung Smashpot Learn More

ABS+ damper with MILO remote lockout kit
Fits 2020+ Manitou R7 Pro, R7 Expert & Machete Comp forks
Threads M29.6x0.8mm.
Can be converted to crown adjust.

Manitou Part Code: 141-38117-K029 Learn More